A Novel BESO Methodology for Topology Optimization of ‎Reinforced Concrete Structures: A Two-loop Approach

Document Type : Research Paper

Authors

1 Graduate Program in Civil Engineering, Federal University of Rio Grande do Sul,‎ Av. Osvaldo Aranha, 99, 3º Andar, 90035-190, Porto Alegre, RS. Brazil‎

2 Graduate Program in Mechanical Engineering, Federal University of Rio Grande do Sul,‎ Av. Sarmento Leite, 425, Sala 202, 2º Andar, 90050-170, Porto Alegre, RS. Brazil‎

3 Graduate Program in Computational Modeling, Federal University of Rio Grande (FURG),‎ School of Engineering, km 8 Itália Avenue, Rio Grande, 96201-900, Brazil‎

Abstract

A new topology optimization methodology for reinforced concrete structures is proposed. The structures are optimized in two iterative loops, where different sensitivity criteria are used to determine the regions to be topologically optimized. For the first loop, the compliance criterion is used to determine the higher compliance elements and, consequently, remove the concrete from the computational domain. In the next loop, only failed concrete regions (Ottosen failure surface) are replaced by reinforcement, ensuring that complies with the von Mises criterion. In the end, the sizing of the reinforcements is obtained based on the principal forces in the steel regions. Results regarding the mechanical behavior, cost, volume, and mass of the optimized structures are presented in this study. A case study indicated that the proposed methodology can lead to volume, mass, and cost reductions of 20%, 21.5%, and 56%, respectively.

Keywords

Main Subjects

Publisher’s Note Shahid Chamran University of Ahvaz remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

[1] Liang, Q.Q., Xie, Y.M., Steven, G.P., Topology Optimization of Strut-and-Tie Models in Reinforced Concrete Structures Using an Evolutionary Procedure, ACI Structural Journal, 97, 2000, 322-332.
[2] Nagarajan, P., Pillai, T.M.M., Development of strut and tie models for simply supported deep beams using topology optimization, Journal of Structural Engineering (Madras), 30, 2008, 641-747.
[3] Xia, Y., Langellar, M., Hendriks, M.A.N., Automated optimization-based generation and quantitative evaluation of Strut-and-Tie models, Computers & Structures, 238, 2020, 106297.
[4] Lanes, R.M., Greco, M., Guerra, M.B.B.F., Strut-and-tie models for linear and nonlinear behavior of concrete based on topological evolutionary structure optimization (ESO), IBRACON Structures and Materials Journal, 12, 2019, 87-100.
[5] Xia, Y., Langellar, M., Hendriks, M.A.N., A critical evaluation of topology optimization results for strut-and-tie modeling of reinforced concrete, Computer-Aided Civil and Infrastructure Engineering, 35, 2020, 850-869.
[6] Cedrim M.B.M., Lages, E.N., Barboza, A.S.R., Proposition and analysis of strut and tie models for short corbels from techniques of topology optimization, IBRACON Structures and Materials Journal, 14, 2021, 14212.
[7] Lee, D.-K., Yang, C.-J., Starossek, U., Topology design of optimizing material arrangements of beam-to-column connection frames with maximal stiffness, Scientia Iranica, 19, 2012, 1025-1032.
[8] Shobeiri, V., Ahmadi-Nedushan, B., Bi-directional evolutionary structural optimization for strut-and-tie modelling of three-dimensional structural concrete, Engineering Optimization, 49, 2017, 2055-2078.
[9] Dey, S., Karthik, M.M., Modelling four-pile cap behaviour using three-dimensional compatibility strut-and-tie method, Engineering Structures, 198, 2019, 109499.
[10] Almeida, V.S., Simonetti, H.L., Neto, L.O., The strut-and-tie models in reinforced concrete structures analysed by a numerical technique, IBRACON Structures and Materials Journal, 6, 2013, 139-157.
[11] El-Metwally, S.E., Chen, W.-F., Structural Concrete: Strut-and-Tie Models for Unified Design, Taylor & Francis Group, 2018.
[12] Goodchild, C.H., Morrison, J., Vollum, R.L., Strut-and-tie Models – How to design concrete members using strut-and-tie models in accordance with Eurocode 2, MPA The Concrete Centre, 2014.
[13] Reineck, K.-H., ACI SP-208, Examples for the Design of Structural Concrete with Strut-and-tie Models, American Concrete Institute, 2002.
[14] Wight, J.K., Reinforced Concrete – Mechanics and Design, Pearson Education, Inc., 2015.
[15] Bendsøe, M.P., Sigmund, O., Topology Optimization: Theory, Method and Application, Springer, Berlin, 2003.
[16] Da, D., Xia, L., Li, G., Huang, X., Evolutionary topology optimization of continuum structures with smooth boundary representation, Structural and Multidisciplinary Optimization, 57, 2018, 2143-2159.
[17] Fu, Y.-F., Rolfe, B., Chiu, L.N.S., Wang, Y., Huang, X., SEMDOT: Smooth-edged material distribution for optimizing topology algorithm, Advances in Engineering Software, 150, 2020, 102921.
[18] Biyikli, E., To, A.C., Proportional Topology Optimization: A New Non-Sensitivity Method for Solving Stress Constrained and Minimum Compliance Problems and Its implementation in MATLAB, PLoS ONE, 10, 2015, 0145041.
[19] Huang, X., Xie, Y.M., Evolutionary topology optimization of continuum structures: methods and applications, John Wiley & Sons, UK, 2010.
[20] Sethian, J.A., Wiegmann, A., Structural boundary design via level set and immersed interface methods, Journal of Computational Physics, 2, 2000, 489-528.
[21] Michell, A.G.M., The limits of economy of material in frame-structures, The London, Edinburgh, and Dublin Philosophical Magazine and Journal of Science, 8, 1904, 589-597.
[22] Kumar, P., Optimal force transmission in reinforced concrete deep beams, Computers and Structures, 8, 1978, 223-229.
[23] Kwak, H.G., Noh, S.H., Determination of strut-and-tie models using evolutionary structural optimization, Engineering Structures, 28, 2006, 1440–1449.
[24] Bołbotowsk, K., Sokół, T., New method of generating Strut and Tie models using truss topology optimization, PCM-CMM-2015 – 3rd Polish Congress of Mechanics & 21st Computer Methods in Mechanics, 2, 2015, 625-626.
[25] Liang, Q.Q., Steven, G.P., A performance-based optimization method for topology design of continuum structures with mean compliance constraints, Computer Methods in Applied Mechanics and Engineering, 191, 2002, 1471-1489.
[26] Liang, Q.Q., Ng, A.W.M., Performance‐based optimization of strut‐and‐tie models in reinforced concrete deep beams, Innovations in Structural Engineering and Construction, Proceedings of the Fourth International Structural Engineering and Construction Conference, 2007.
[27] Guest, J.K., Moen, C.D., Reinforced concrete design with topology optimization, 19th Analysis & Computation Specialty Conference, 2010.
[28] Bendsøe, M.P., Kikuchi, N., Generating optimal topologies in structural design using a homogenization method, Computer Methods in Applied Mechanics and Engineering, 1, 1988, 197-224.
[29] Ramani, A., Multi-material topology optimization with strength constraints, Structural and Multidisciplinary Optimization, 43, 2011, 597-615.
[30] Blasques, J.P., Multi-material topology optimization of laminated composite beams with eigenfrequency constraints, Composite Structures, 111, 2014, 45-55.
[31] Cui, M., Chen, H., Zhou, J., Wang, F., Multi-material proportional topology optimization based on the modified interpolation scheme, Engineering with Computers, 34, 2017, 287-305.
[32] Florea, V., Pamwar, M., Sangha, B., Kim, Y., 3D multi-material and multi-joint topology optimization with tooling accessibility constraints, Structural and Multidisciplinary Optimization, 60, 2019, 2531-2558.
[33] Liang, Q.Q., Xie, Y.M., Steven, G.P., Generating optimal strut-and-tie models in prestressed concrete beams by performance-based optimization, ACI Structural Journal, 98, 2001, 226-232.
[34] Liang, Q.Q., Performance-based optimization of strut-and-tie models in reinforced concrete beam-column connections, Real Structures: Bridges and Tall Buildings, Proceedings of the Tenth East Asia-Pacific Conference on Structural Engineering and Construction, 2006.
[35] Qiu, Y., Liu, X., Comparison on construction of strut-and-tie models for reinforced concrete deep beams, Journal of Central South University of Technology, 18, 2011, 1685-1692.
[36] Lee, D.K., Yang, C.J., Starossek, U. Topology design of optimizing material arrangements of beam-to-column connection frames with maximal stiffness, Scientia Iranica, 19, 2012, 1025-1032.
[37] Zhong, J.T., Wang, L., Deng, P., Zhou, M., A new evaluation procedure for the strut-and-tie models of the disturbed regions of reinforced concrete structures, Engineering Structures, 148, 2017, 660-672.
[38] Xia, Y., Langelaar, M., Hendriks, M.A.N., Automated optimization based generation and quantitative evaluation of strut-and-tie models, Computers and Structures, 238, 2020, 106297.
[39] Xia, Y., Langelaar, M., Hendriks, M.A.N., A critical evaluation of topology optimization results for strut-and-tie modeling of reinforced concrete, Computer-aided Civil and Infrastructure Engineering, 35, 2020, 850-869.
[40] Xia, Y., Langelaar, M., Hendriks, M.A.N., Optimization-based three-dimensional strut-and-tie model generation for reinforced concrete, Computer-aided Civil and Infrastructure Engineering, 36, 2020, 526-543.
[41] Zhou, L., He, Z., Liu, Z., Investigation of optimal layout of ties in STM developed by topology optimization, Structural Concrete, 17, 2016, 175-182.
[42] Wang, L., Zhag, H., Zhu, M., Chen, Y.F., A new Evolutionary Structural Optimization method and application for aided design to reinforced concrete components, Structural and Multidisciplinary Optimization, 62, 2020, 2599–2613.
[43] Novatny, A.A., Lopes, C.G., Santos, R.B., Topological derivative-based topology optimization of structures subject to self-weight loading, Structural and Multidisciplinary Optimization, 63, 2021, 1853–1861.
[44] Bruyneel, M., Duysinx, P., Note on topology optimization of continuum structures including self-weight, Structural and Multidisciplinary Optimization, 29, 2005, 245-256.
[45] Amaral, R.R., Borges, J.A., Gomes, H.M., Proportional topology optimization under reliability-based constraints, Journal of Applied and Computational Mechanics, 8, 2022, 319–330.
[46] Li, Q., Steven, G.P., Xie, Y.M., On equivalence between stress criterion and stiffness criterion in evolutionary structural optimization, Structural Optimization, 18, 1999, 67–73.
[47] CEB-FIB, CEB-FIP Model Code 1990 - Design Code, Thomas Telford, 1993.
[48] Novak, L.C., Sprenger, H., Example 4: Deep Beam with opening, In: ACI SP-208, Examples for the Design of Structural Concrete with Strut-and-tie Models, Editor Karls-Heinz Reineck, ACI SP-208, 2002.